Driveways and paths · Tyne and Wear

New tarmac driveways in Newburn

Every new tarmac driveway we price in Newburn comes with a written specification, so the dig depth, sub-base, binder course and surface course are on paper before anything is agreed.

NEWBURN GUIDE£56–£88 per m² inc VAT
Wide new tarmac driveway with granite sett border leading to a garage, typical of new tarmac driveway work

How much should I budget in Newburn?

Local guide rates for Newburn (the North East, about 7% below our UK midpoint):

ItemGuide price (inc VAT)
New black tarmac drive, full dig-out and new sub-base£56–£88 per m²
Example: 30 m² drive£1,850–£2,900
Example: 50 m² drive£2,800–£4,400
Example: 80 m² drive£4,450–£7,050

As a 2026 guide in Newburn, new tarmac driveway work runs at about £56–£88 per m² including VAT, so a 30 m² drive is roughly £1,850–£2,900. Guide only; the survey confirms a fixed price.

Where we work in and around Newburn

Newburn at a glance. Newburn sits 5 miles from Newcastle upon Tyne, within our regular Tyne and Wear cover.

Postcodes
NE15, NE40, NE5, NE20
Area
Tyne and Wear
Nearest towns
Blaydon-on-Tyne (2 miles), Whickham (4 miles), Prudhoe (5 miles), Gosforth (5 miles)
Pricing
North East, about 7% below our UK midpoint
Kerb approvals
The highway authority

The same service is available in Blaydon-on-Tyne, Whickham, Prudhoe, Gosforth, Newcastle upon Tyne.

What the price covers

A new tarmac driveway is built from the ground up: the old surface and soil are dug out, a compacted stone sub-base is laid, then a hot binder course and a finer surface course are spread and rolled, and the edges are held by kerbs or blocks.

  • Dig to formation level, usually around 230–250 mm below finished height
  • Geotextile membrane where the ground is soft or clay
  • Concrete-haunched kerbs or a block-paved border as edge restraint
  • Binder course (AC 20 dense), about 50–60 mm, laid hot and rolled
  • Falls set so water runs to a channel, gully or soft landscaping

Planning and kerb rules for Newburn

In England, householder permitted development (Class F of the 2015 General Permitted Development Order) lets you lay a hard surface in front of a house without planning permission if it is porous, or if the rainwater is directed to a permeable area within the property. If the area is more than 5 m² and neither applies, you need permission. Standard dense tarmac is not porous, so a dense tarmac drive needs a lawn, border, channel to a soakaway or other permeable route for its water. If the job needs a dropped kerb, the highway authority (the county or unitary council) approves it before any work on the footway.

The build-up we price

Surface course20–30 mm AC 6 denseBinder course50–60 mm AC 20 denseSub-baseabout 150 mm MOT Type 1Edgeskerbs or blocks on a concrete haunchINDICATIVE CROSS-SECTION · NOT TO SCALE

Your questions answered

Will someone visit before I get a fixed price in Newburn?

Yes for new surfacing such as drives, paths, private roads and car parks. Small repairs are often priced from photos; if a visit is needed for a repair-only job, we tell you any charge first.

Do you work in my part of Newburn?

We cover Newburn including NE15, NE40, NE5, NE20, and nearby Blaydon-on-Tyne, Whickham, Prudhoe.

What approvals apply in Newburn?

In England, a new hard surface over 5 m² in front of a house needs planning permission unless it is porous or drains to a lawn, border or soakaway within the property. Dropped kerbs are approved by the highway authority (the county or unitary council).

New tarmac driveway cost in Newburn: what should I budget?

As a 2026 guide in Newburn, new tarmac driveway work runs at about £56–£88 per m² including VAT, so a 30 m² drive is roughly £1,850–£2,900. Edging, drainage and a dropped kerb are priced separately where needed.

Also in Newburn

Tell us what you have in mind for Newburn and we'll book a survey and put the specification in writing.

Free survey for new surfacing

New tarmac driveways in Newburn: get a written quote

Send a postcode and a rough size and we'll arrange a survey. Every quote lists the layers, edging, drainage and VAT.

  • Surface courseDEPTH + MIX
  • Binder courseDEPTH + MIX
  • Sub-baseDEPTH + MATERIAL
  • Edges, drainage, VATITEMISED
Call nowGet a price